64-Point FT Chip
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
project topics
Active In SP

Posts: 2,492
Joined: Mar 2010
03-04-2010, 07:21 PM

The complete structure of a modern specified by the IEEE 802.11a standard is shown in . It consists of a data scrambler, modulator, convolutional encoder, interleaver, 64-point IFFT/FFF, demodulator, deinterleaver, Viterbi decoder, and descrambler. The standard specifies a data rate ranging from 6 to 54 Mb/s. Depending on the de d rate, the modulation scheme adopted can be binary phase shift keying (BPSKt, quaternary phase shift keying (QPSK), or quadrature amplitude modulation(QAM) with l-6bit/subcarrier. Fourth generation wireless and mobile system are currently the focus of research and development. Broadband wireless system based on orthogonal frequency division multiplexing will allow packet based high data rate communication suitable for video transmission and mobile internet application. Considering this fact we proposed a data path architecture using dedicated hardwire for the baseband processor. The most computationally intensive part of such a high data rate system are the 64-point inverse FFT in the transmit direction and the viterbi decoder in the receiver direction. Accordingly an appropriate design methodology for constructing them has to be chosen a) how much silicon area is needed b) how easily the particular architecture can be made flat for implementation in VLSI c) in actual implementation how many wire crossings and how many long wires carrying signals to remote parts of the design are necessary d) how small the power consumption can be. This paper describes a novel 64-point FFT/IFFT processor which has been developed as part of a large research project and implimentation to develop a single chip wireless modem.

The encoding rates supported in the standard are 1/2, 2/3, and 3/4. The bandwidth of the transmitted signal is 20 MHz and the OFDM symbol duration is 4 ?s including 0.8 ?s for a guard interval [1 ] Thus, in effect, FFT/TFFT has to be computed within 4 ?

In general, the FFT implementations typically fall into one of the two categories: 1) methods based on direct Fourier transform [and 2) methods based on direct hardware implementations of established FFT signal flow graphs [8] [14]. A problem with these solutions is that the approach adopted on the algorithmic level typically takes little account of its implications at the architecture, data flow, or chip design levels. Thus, many of these designs [8]-[10] may be irregular, dominated by wiring, and may have heavy overheads in terms of data storage [15] In a complex system, deployment of such strategies may result in severe disadvantages, because of the tight timing constraints and implicit requirement of low power consumption.

The conventional Cooley-Tukey radix-2 FFT algorithm requires 192 complex butterfly operations for a 64-point FFT computation. Considering that one FF1' has to be computed within 4?s, one butterfly operation has to be completed within 20,8 ns which results in 48 MHz clock frequency for a single butterfly architecture. The synthesis result for a radix-2 butterfly unit (one complex multiplication and two complex additions) in 1HP O.25?m- technology shows that it occupies 0.18-mm area and dissipates 17 mW power at that frequency. On top of this butterfly unit, one needs memory to store the complex twiddle factors and complex intermediate data, serial-to-parallel and parallel-to-serial converters at the inputs and outputs, respectively, complicated addressing logic and control circuitry. Combining all these circuit modules it is expected that the power dissipation of the entire processor will be quite high. Moreover, the input data arrives at 20 MHz clock frequency, and thus, it is more appropriate to operate the FFT module at that frequency. In order to satisfy the time constraint at this frequency, one has to employ multiple butterfly units in parallel, which in turn increases the area and power dissipation. Alternatively, since most of the implementations of the IEEE 802.1 1a standard oversample the incoming data at 40 or 80 MHz, a single radix-2 butterfly based FFT module should be operated at 80 MHz clock frequency (the next available frequency to the actually required frequency). This approach satisfies the timing constraint, but at the cost of high power consumption.
In order to speed up the FFT computation, more advanced solutions have been proposed using an increase of the radix [15] [16]. These approaches result in increase of arithmetic complexity within the butterfly itself. The radix-4 FFT algorithm is most popular and has the potential to satisfy the current need. However, a single radix-4 butterfly requires three complex multiplications and eight complex additions. Thus, in order to carry out one radix-4 butterfly operation per clock cycle, one needs to complete 12 real multiplications and 16 real additions at each cycle. Since multipliers are typically very power-hungry elements in a VLSI design, this type of arrangement results in significant power consumption.
Use Search at http://topicideas.net/search.php wisely To Get Information About Project Topic and Seminar ideas with report/source code along pdf and ppt presenaion

Important Note..!

If you are not satisfied with above reply ,..Please


So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page
Tagged Pages: pdf 64 point ft chip, 64 point fft butterfly, 64point ft chip, 64 point fft chip, 64 point ft chip, seminar report on 64 point ft chip, 64 point ft chip seminar abstract,
Popular Searches: design and implementation of 64 point fft ifft for ieee 802 11a, 64 point ft importance, 64 point ft chip seminar abstract, 64 point ft chip, fft dif butterfly, 64 point fft chip doc, implementation of wlan physical layer standard for ieee 802 11a and ieee 802 11b,

Quick Reply
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  Wireless Battery Charger Chip for Smart-Card Applications full report project topics 8 7,544 28-01-2013, 03:02 PM
Last Post: varna prasad
  Power Point Tracking for Photovoltaic Systems full report computer science technology 1 3,174 19-01-2013, 12:51 PM
Last Post: seminar tips