Cryogenic cooling in machining processes
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
seminar surveyer
Active In SP

Posts: 3,541
Joined: Sep 2010
23-12-2010, 12:59 PM

Presented by: Kulkarni Aniket P.

.pptx   10TH08F-Cryogenic cooling in machining processes.pptx (Size: 91.06 KB / Downloads: 167)

The cooling applications in machining operations play a very important role and many operations cannot be carried out efficiently without cooling.
Application of a coolant in a cutting process can increase tool life and dimensional accuracy, decrease cutting temperatures, surface roughness and the amount of power consumed in a metal cutting process .
Thus, it become mandatory to use coolant in machining operations.

Cutting fluids i.e. coolants
There are two categories
i)Conventional cutting fluids.
a)Water soluble cutting fluids
b)Mineral oils

ii)Cryogenic cutting fluids.
Here, liquid nitrogen is used as a cryogenic coolant.

Application of conventional fluids create some techno-environmental problems such as,
Environmental pollution due to chemical dissociation or break up due to high cutting temperature.
Biological (Dermatological) problems to operators coming in physical contact.
Water pollution & Soil contamination during disposal.
So, it is absolutely necessary to use an environmentally acceptable coolant in manufacturing industry.
For this purpose, liquid nitrogen as a cryogenic coolant has been explored.

Properties of N2
Triple point : 63.148 K
Normal Boiling Point :77.313 K
Critical Point : 126.19K
It is the most abundant gas, composes about four-fifths (78.03%) by volume of the atmosphere.
It is a colourless, odourless,tasteless and non-toxic gas.
These characteristics of liquid nitrogen have made it as a preferred coolant.
Cryogenic cooling approaches
Cryogenic cooling approaches in material machining could be classified into four groups
Cryogenic pre-cooling the of work piece.
Indirect cryogenic cooling.
Cryogenic spraying and jet cooling.
Cryogenic treatment.
Cryogenic pre-cooling the of work piece.
Here,aim is to cool work piece or chip to change properties of material from ductile to brittle because, the ductile chip material can become brittle when the chip temperature is lowered and become easy to dispose
This achieved by
Pouring the liquid nitrogen by continually onto the work piece.
Disadavatage of this method are,
High LN2 consumption
Dimensional changes may occur

Indirect cryogenic cooling
This method was also called conductive remote cooling.
Here,the aim is to cool the cutting point through heat conduction.
In this method, instead of tool tip, tool shank is cooled by LN2.
Hence,LN2 does not contact with the workpiece and it does not cause significant change in properties of the work piece , in addition, cooling effect is stable.
Disadvantages are : effect of this approach is highly dependent on
thermal conductivity of the cutting tool material,
the distance from the LN2 source to the

Cryogenic spraying and jet cooling.
The objective in this method is to cool cutting zone,particularly tool–chip interface with liquid nitrogen by using nozzles.
Here,workpiece will constant temperature and not subject to dimensional inaccuracy and geometrical Distortion
this localised cryogenic cooling reduces the tool
face temperature, enhances its hardness, and so reduces its wear rate;
This approach also embrittles the chip by
cold temperature and bend the chip with the chip breaker.

This cryogenic machining approach eliminates the BUE problem on tools because the cold temperature reduces the possibility of chips welding to the tool and the high pressure
cryogenic jet also helps to remove possible BUE formation
Therefore, it will produce better surface quality.
Cryogenic treatment
Cryogenic treatment is a process similar to heat treatment. In this method, samples are cooled down to cryogenic temperature and maintained at this temperaturefor a long time and then heated back to room temperature to improve wear resistance and dimensional stability of them.
However, the effect of the cryogenic treatment on cutting performance is not stable for all machiningapplications and cutting conditions, and there was not seen a comparison between cryogenic treatment and other cryogenic cooling approaches.
Effects of the cryogenic cooling in machining processes
The effect of cryogenic cooling on tool wear and tool life
Tool wear decreases considerably And tool life increases around four times , for steels.
The effect of cryogenic cooling on surface roughness and dimensional deviation
In application of indirect cryogenic cooling, the surface
rough nesses of materials machined with LN2 cooling were
found to be much better than the surface roughness of
materials machined without LN2 cooling after the same
length of cutting.
The effect of cryogenic cooling on friction
LN2 lubricated contact produced lower friction coefficient than the dry sliding contact and the emulsion-lubricated contact.

The effect of cryogenic cooling on cutting forces
Energy consumption in a cutting operation was associatedwith friction and cutting forces. So, it is significant being cutting forces less in terms of productivity and production cost in any machining process.
According to some researchers, cryogenic cooling did not significantly alter the cutting forces in machining of different materials.

When compared with dry cutting and conventional cooling, the most considerable characteristics of the cryogenic cooling application in machining operations
could be determined as enabling substantial improvement in tool life and surface finish-dimensional accuracy through reduction in tool wear through control of machining temperature desirably at the cutting zone.

Yakup Yildiz, Muammer Nalbant, A review of cryogenic cooling in machining processes,2008
N.R.Dhar,S.Paul,A.B.Chattopadhyay,“Machinig of AISI 4041 steel under croygenic cooling –Tool wear, surface roughness, dimensional variation”,2002
Cryogenic Engineering, Thomas M. Flynn

Important Note..!

If you are not satisfied with above reply ,..Please


So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page
Tagged Pages: cryogenic cooling in machining, cryogenics cutting ppt, cryogenic cooling in turning operation, cryogenic cooling in machining process pdf, cryogenic spraying with jet, projects presentation of improve in coolant life for machining process, applications of cryogenic cooling,
Popular Searches: integration of processes, hybrid machining processes ppt, optimization of machining parameter of cutting processes, ppt on advanced machining processes, detailed information on hybrid machining processes, abstract for mechanical advanced machining processes, advanced machining processes ppt,

Quick Reply
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  Robust Nonlinear Model Predictive Control of Batch Processes pdf study tips 0 575 05-07-2013, 04:23 PM
Last Post: study tips
  Cryogenic CO2 capture usingdynamicallyoperatedpackedbeds project uploader 0 404 18-08-2012, 12:25 PM
Last Post: project uploader
  Nanofluids for Improved Efficiency in Cooling Systems seminar ideas 0 650 24-07-2012, 03:17 PM
Last Post: seminar ideas
  NATURAL GAS TREATMENT PROCESSES seminar ideas 0 739 24-07-2012, 02:23 PM
Last Post: seminar ideas
  Handbook of Petroleum Refining Processes project uploader 0 678 25-06-2012, 11:39 AM
Last Post: project uploader
  DMS cyclone separation processes for optimization of plastic wastes recycling seminar ideas 0 784 01-06-2012, 02:02 PM
Last Post: seminar ideas
  Casting Processes seminar surveyer 1 1,265 26-05-2012, 02:47 PM
Last Post: seminar flower
  Resin Bed Regeneration in Water Treatment Processes seminar flower 0 1,049 19-05-2012, 03:34 PM
Last Post: seminar flower
  Cryogenic Refrigeration (Freezing ) seminar class 0 1,653 22-04-2011, 04:35 PM
Last Post: seminar class
  CRYOGENIC FREEZING seminar surveyer 0 748 23-12-2010, 12:24 PM
Last Post: seminar surveyer