How Cell Phones Work
Active In SP
Joined: Sep 2010
22-12-2010, 03:02 PM
How Cell Phones Work.ppt (Size: 675 KB / Downloads: 302)
An Important Technology
Cellular telephony is one of the fastest growing technologies on the planet.
Presently, we are starting to see the third generation of the cellular phones coming to the market.
New phones allow users to do much more than hold phone conversations.
Store contact information
Make task/to-do lists
Keep track of appointments
Send/receive video clips
Get information from the internet
Integrate with other devices (PDA’s, MP3 Players, etc.)
Outline for Today
Today, we will review the design of cellular system: what are its key components, what it is designed like, and why.
Also, we will look at how cellular networks support multiple cell phone users at a time.
Finally, we will review the important generations of cellular systems and start looking at the design of the first generation of cell phones.
The Cellular Concept
Cellular system developed to provide mobile telephony: telephone access “anytime, anywhere.”
First mobile telephone system was developed and inaugurated in the U.S. in 1945 in St. Louis, MO.
This was a simplified version of the system used today.
A base station provides coverage (communication capabilities) to users on mobile phones within its coverage area.
Users outside the coverage area receive/transmit signals with too low amplitude for reliable communications.
Users within the coverage area transmit and receive signals from the base station.
The base station itself is connected to the wired telephone network.
First Mobile Telephone System
Problem with Original Design
Original mobile telephone system could only support a handful of users at a time…over an entire city!
With only one high power base station, users phones also needed to be able to transmit at high powers (to reliably transmit signals to the distant base station).
Car phones were therefore much more feasible than handheld phones, e.g., police car phones.
Over the next few decades, researchers at AT&T Bell Labs developed the core ideas for today’s cellular systems.
Although these core ideas existed since the 60’s, it was not until the 80’s that electronic equipment became available to realize a cellular system.
In the mid 80’s the first generation of cellular systems was developed and deployed.
The Core Idea: Cellular Concept
The core idea that led to today’s system was the cellular concept.
The cellular concept: multiple lower-power base stations that service mobile users within their coverage area and handoff users to neighboring base stations as users move. Together base stations tessellate the system coverage area.
Thus, instead of one base station covering an entire city, the city was broken up into cells, or smaller coverage areas.
Each of these smaller coverage areas had its own lower-power base station.
User phones in one cell communicate with the base station in that cell.
3 Core Principles
Small cells tessellate overall coverage area.
Users handoff as they move from one cell to another.
Some group of small regions tessellate a large region if they over the large region without any gaps or overlaps.
There are only three regular polygons that tessellate any given region.
Three regular polygons that always tessellate:
Circular Coverage Areas
Original cellular system was developed assuming base station antennas are omnidirectional, i.e., they transmit in all directions equally.
Circles Don’t Tessellate
Thus, ideally base stations have identical, circular coverage areas.
Problem: Circles do not tessellate.
The most circular of the regular polygons that tessellate is the hexagon.
Thus, early researchers started using hexagons to represent the coverage area of a base station, i.e., a cell.
Thus the Name Cellular
With hexagonal coverage area, a cellular network is drawn as:
Since the network resembles cells from a honeycomb, the name cellular was used to describe the resulting mobile telephone network.
A crucial component of the cellular concept is the notion of handoffs.
Mobile phone users are by definition mobile, i.e., they move around while using the phone.
Thus, the network should be able to give them continuous access as they move.
This is not a problem when users move within the same cell.
When they move from one cell to another, a handoff is needed.
A user is transmitting and receiving signals from a given base station, say B1.
Assume the user moves from the coverage area of one base station into the coverage area of a second base station, B2.
B1 notices that the signal from this user is degrading.
B2 notices that the signal from this user is improving.
A Handoff (Cont’d)
At some point, the user’s signal is weak enough at B1 and strong enough at B2 for a handoff to occur.
Specifically, messages are exchanged between the user, B1, and B2 so that communication to/from the user is transferred from B1 to B2.
Extensive frequency reuse allows for many users to be supported at the same time.
Total spectrum allocated to the service provider is broken up into smaller bands.
A cell is assigned one of these bands. This means all communications (transmissions to and from users) in this cell occur over these frequencies only.
Frequency Reuse (Cont’d)
Neighboring cells are assigned a different frequency band.
This ensures that nearby transmissions do not interfere with each other.
The same frequency band is reused in another cell that is far away. This large distance limits the interference caused by this co-frequency cell.
More on frequency reuse a bit later.
Example of Frequency Reuse
Multiple Access in Cellular Networks
Multiple Transmitters, One Receiver
In many wireless systems, multiple transmitters attempt to communicate with the same receiver.
For example, in cellular systems. Cell phones users in a local area typically communicate with the same cell tower.
How is the limited spectrum shared between these local transmitters?
Multiple Access Method
In such cases, system adopts a multiple access policy.
Three widely-used policies:
Frequency Division Multiple Access (FDMA)
Time Division Multiple Access (TDMA)
Code Division Multiple Access (CDMA)
In FDMA, we assume that a base station can receive radio signals in a given band of spectrum, i.e., a range of continuous frequency values.
The band of frequency is broken up into smaller bands, i.e., subbands.
Each transmitter (user) transmits to the base station using radio waves in its own subband.
A subband is also a range of continuous frequencies, e.g., 824 MHz to 824.1 MHz. The width of this subband is 0.1 MHz = 100 KHz.
When a users is assigned a subband, it transmits to the base station using a sine wave with the center frequency in that band, e.g., 824.05 MHz.
When the base station is tuned to the frequency of a desired user, it receives no portion of the signal transmitted by another in-cell user (using a different frequency).
This way, the multiple local transmitters within a cell do not interfere with each other.
In pure TDMA, base station does not split up its allotted frequency band into smaller frequency subbands.
Rather it communicates with the users one-at-a-time, i.e., “round robin” access.
Time is broken up into time slots, i.e., small, equal-length intervals.
Assume there are some n users in the cell.
Base station groups n consecutive slots into a frame.
Each user is assigned one slot per frame. This slot assignment stays fixed as long as the user communicates with the base station (e.g., length of the phone conversation).
Example of TDMA time slots for n = 10.
In each time slot, the assigned user transmits a radio wave using a sine wave at the center frequency of the frequency band assigned to the base station.
The TDMA used by real cellular systems (like AT&T’s) is actually a combination of FDMA/TDMA.
Base station breaks up its total frequency band into smaller subbands.
Base station also divides time into slots and frames.
Each user is now assigned a frequency and a time slot in the frame.
Hybrid FDMA/TDMA (Cont’d)
CDMA is a more complicated scheme.
Here all users communicate to the receiver at the same time and using the same set of frequencies.
This means they may interfere with each other.
The system is designed to control this interference.
A desired user’s signal is deciphered using a unique code assigned to the user.
There are two types of CDMA methods.
CDMA Method 1: Frequency Hopping
First CDMA technique is called frequency hopping.
In this method each user is assigned a frequency hopping pattern, i.e., a fixed sequence of frequency values.
Time is divided into slots.
In the first time slot, a given user transmit to the base station using the first frequency in its frequency hopping sequence.
Frequency Hopping (Cont’d)
In the next time interval, it transmits using the second frequency value in its frequency hop sequence, and so on.
This way, the transmit frequency keeps changing in time.
We will look at frequency hopping in greater detail in an exercise (in a bit).
Second Type of CDMA: Direct Sequence
This is a more complicated version of CDMA.
Basically, each in-cell user transmits its message to the base station using the same frequency, at the same time. Here signals from different users interfere with each other.
But the user distinguishes its message by using a special, unique code. This code serves as a special language that only the transmitter and receiver understand. Others cannot decipher this language.
Direct Sequence CDMA
Because of the complexity of this second type of CDMA, we will not describe it in detail.
Rather we will give an intuitive understanding of it.
Specifically, think of this access scheme like a group of conversations going on in a cocktail party.
Cocktail Party Analogy
In this cocktail party, people talk to each other at the same time and thus “interfere” with other.
To keep this interference in control, we require that all partiers must talk at the same volume level; no one partier shouts above anybody else.
Also, to make sure that each speaking partier is heard correctly by his/her intended listener (and nobody else can listen in), we require each speaker to use a different language to communicate in.
Cocktail Party (Cont’d)
The caveat in this analogy is that if you speak in one language, it is assumed that only your desired listener can understand this language.
Thus, if you were at this party and only understood one language, say English, then all non-English conversations would sound like gibberish to you.
The only signal you would understand is English, coming from your intender speaker (transmitter).
Similar methodology is used by Direct Sequence CDMA transmitters/receivers.
Exercise on Frequency Hopping CDMA
Assume you are the receiver (base station) in a frequency hopping cellular system.
There are a total of 10 users in your cell.
They are each assigned their own unique frequency hopping pattern.
Exercise Description (Cont’d)
A user will use its frequency hopping pattern to transmit messages to the base station.
In the first time slot, the user will transmit using the first frequency value in the frequency hopping sequence.
In the second time slot, the user will use the second frequency value in the hopping sequence, and so on.
Exercise Description (Cont’d)
Assume that the base station (you) can receive signals in the range of 824 MHz to 825 MHz.
This means that you have 1 MHz of frequency available for use to communicate with local users.
The network designers decided to divide the total 1 MHz = 1000 KHz of frequency assigned to you into 100 KHz subbands, i.e., into 10 subbands.
Additionally, the designers have divided time into 1 millisecond (1 millisecond = 0.001 second) time slots.
Exercise Description (Cont’d)
In the handout, you will see a sequence of bits for different frequency and time value.
These sequences represent the messages that the base station determines from the received radio waves (after demodulation) at the different frequency and time values.
Exercise Description (Cont’d)
In each handout, a desired user’s frequency hopping pattern is given.
Please use this hopping pattern, to determine the bit sequence of the desired user.
Exercise Description (Cont’d)
Now, assume that each user is sending a text message to the base station.
We wish to determine this message.
To do so, break up the bit sequence into sequence of bytes.
Recall, 1 byte = 8 bits.
Exercise Description (Cont’d)
Computers use a standard method to convert letters we use to write text messages, i.e., the letters of the alphabet, into bits (sequences of 0’s and 1’s).
This standard method is called ASCII coding.
In the handout, we show a part of the ASCII codebook.
Exercise Description (Cont’d)
The codebook can be used to determine the text message sent by the user.
For each byte, we lookup the byte sequence in the codebook (chart) to determine the letter that it corresponds to.
String the letters together to get the text message.
Important Parameter in Exercise
In the system described in the exercise, a user transmits 3 bytes in 6ms, where 1ms = 0.001 seconds.
There are 8 bits in a byte; so the user transmits 24 bits in 6ms.
This means the user has a data rate of 24 bits/6ms = 4000 bits/sec.
Final Points on FDMA/TDMA/CDMA
When users are in the middle of a phone call, the system uses FDMA/TDMA/CDMA to give them access.
But there are only so many frequencies, time-slots, or codes available to share between users in a cell.
If we divide the frequency into too many bands, or use too many time slots, or too many codes, the quality of speech heard by the end user will be unsatisfactory.
Channel is a general term which refers to a frequency in an FDMA system, a timeslot/frequency combination in TDMA, or a code in CDMA.
This way, a base station has a fixed number of channels and can support only that many simultaneous users.
Random Access: Another Important Multiple Access Method
Motivating Random Access Channels
As mentioned earlier, FDMA/TDMA/CDMA are used when users are engaged in a phone call.
Before being assigned a frequency, timeslot, or code (i.e., a channel), a user has to ask the base station if it has a channel leftover to assign this user.
In other words, the user has to have some other way of communicating with the base station.
Motivating Random Access
Of all the frequencies available at a base station, a prescribed portion of them are set aside for this purpose.
These frequencies are called control channels, as opposed to the rest of the frequencies in cell, which are called voice channels.
A user will transmit a signal to the base station on a control channel basically saying, “I’m here and I’d like to talk to you.”
Random Access: Failure
There maybe other users who do this at the same time using the same frequency.
If they do, the signals will interfere with each other and the base station will not receive anything.
This indicates a failure (aka collision), when this happens, each user will backoff for some random amount of time and try again. Since they backoff for a random amount of time, chances are they won’t retry at the same time.
Random Access: Success
If only one user transmits, then the base station will receive the user’s signals and respond to it by saying, “Okay you can talk to me, tune into this other channel and tell me what you want.”
The user will then tune this channel and be able to exclusively transmit and receive signals to the base station.
Random Access: Success (Cont’d)
This new channel assigned to the user is also a control channel.
Using this channel the user can then send a signal that says for example “I want to make a phone to this phone number.”
To which the base station will respond by assigning the user a voice channel, if there are some available.
Random Access Summary
This type of competing access method is called random access.
There are different rules followed by users participating in random access.
We will return to this notion when looking at wi-fi systems.
Standards: Rules for a Cellular Network
The Inner Workings
Government agencies (FCC) give licenses to companies (service providers) to provide cellular access in a particular geographic region.
These licenses allow the service provider to setup cellular towers in that region which can transmit over a prescribed band of frequencies.
The service providers must use one of the approved cellular standards for developing the cellular network in that region.
These standards are mutually agreed upon rules adopted by the industry on how the cell phone system operates.
These standards described the air interface, i.e., how cell phones and base stations must communicate with each other.
More on Standards
These mutually agreed upon standards change over time, as technology progresses.
The first cellular systems deployed in the U.S. adhered to a standard called Analog Mobile Phone System (AMPS). This system existed in the mid 80’s to early 90’s.
The first cellular network used analog technology. Specifically, speech was converted to an FM signal and transmitted back and forth from user phones.
We describe this system in detail a bit later.
Second Generation of Cellular
The second generation (2G) of cellular networks were deployed in the early 90’s.
2G cellular phones used digital technology and provided enhanced services (e.g., messaging, caller-id, etc.).
In the U.S., there were two 2G standards that service providers could choose between.
Second Generation (Cont’d)
The two standards used in U.S. are different from the 2G system used in Europe (called GSM) and the system used in Japan.
First U.S. standard is called Interim Standard 136 (IS-136) and is based on TDMA (time-division multiple access).
Second is called IS-95 and is based on CDMA (code-division multiple access).
Most present systems are what is called the 2.5 generation (2.5G) of cellular.
Present Cellular Systems
Most present cell systems are 2.5G. They offer enhanced services over second generation systems (emailing, web-browsing, etc.).
Some 2.5G systems (such as AT&T’s) are compatible with the European system, Global System Mobile (GSM).
Presently, service providers are setting up third generation (3G) cellular systems.
Present Systems (Cont’d)
3G offers higher data rates than 2.5G. This allows users to send/receive pictures, video clips, etc.
This service is starting to become more and more available in the U.S.
There are two standards for 3G, Wideband CDMA (WCDMA) and cdma2000. These two standards have been adopted world-wide.
Both are based on CDMA principles.
AMPS: A Model for Learning about Cellular Networks
Complete Cellular Network
A group of local base stations are connected (by wires) to a mobile switching center (MSC). MSC is connected to the rest of the world (normal telephone system).
Mobile Switching Centers
Mobile switching centers control and coordinate the cellular network.
They serve as intermediary between base stations that may be handing off users between each other.
Base stations communicate with each via the MSC.
MSC keep track of cell phone user subscription.
MSC connects to the wired phone network (rest of the world).
The AMPS System
AMPS uses FDMA: a service provider is given license to 832 frequencies to use across a geographic region, say a city.
Service provider chops up the city into cells.
Each cell is roughly 10 square miles.
Each cell has a base station that consists of a tower and a small building containing radio equipment.
The AMPS System (Cont’d)
AMPS uses frequency duplexing, i.e., each cell phone uses one frequency to transmit on and another frequency to receive on.
Total 832 channels are divided into half.
One half is used on the uplink, i.e., used by cell phones to transmit to the base station.
The other half is used on the downlink, i.e., used by the base to transmit to cell phone users.
Voice and Control Channels
Of the 832/2 = 416 channels, 21 of them used as control channels.
This means that there are 416-12=395 voice channels.
Now, these voice channels are divided up among the cells based on the frequency reuse.
AMPS: Voice Channels
Frequency Reuse in AMPS
In frequency reuse, a group of local cells use different frequencies to transmit/receive signals in their cell.
This group of local cells is referred to as a cluster.
Clustersize of 7
Assume a clustersize of 7. This means that the total 395 voice channels are divided into groups of seven.
Thus, each cell has about 56 voice channels. This is the most number of users that can be supported in a cell, i.e., roughly 10 square miles in normal environments.
This may/may not be sufficient based on the distribution of users.
Clustersize of 7 (Cont’d)
To see what a system with clustersize of 7 looks like, color a cell with color 1.
This cell (if drawn as a hexagon) has 6 neighbors. Color each of the seven neighbors using a different color (also different from each other).
Now repeat this rule to get the overall “reuse pattern.”
Clustersize of 7, Reuse Pattern
What if we had a smaller cluster?
Now consider a system with a cluster of 4.
Then the number of voice channels per cell is 395/4, which is roughly 98.
Thus, in theory, we can hold more users per cell if this were true.
But there is a problem with a clustersize.
Problem with Smaller Clustersize
Problem with Smaller Clustersize (Cont’d)
If interfering cells are closer, then the total interference power will be larger.
With higher interference power, the quality of the speech signal will deteriorate.
To reduce the interference power, we can make the cells larger.
With larger cell, the number of users covered per unit area reduces. So, the gain (total number of users supported) of a smaller clustersize is not as high as we think.
One way to get more capacity (number of users) while maintaining cell size is to use directional antenna.
Assume antenna which radiates not in alldirections (360 degrees) but rather in 120 degrees only.
Directional Antenna at Base Station
With 120 degree antenna, we draw the cells as:
Directional Antenna (Cont’d)
Because these directional antenna only receive signals in particular direction, the amount of interference power they receive assuming a clustersize of 7 is reduced by 1/3.
With less interference power, the speech quality is much better than it needs to be.
So we can reduce the clustersize (increase interference power) and still have good speech quality.
Trials show that in systems with 120 degree antenna, the clustersize can be as small as 3.
This allows more users to be supported, while keeping cell size fixed.
Because of the benefits offered by 120 degree antenna, these are most readily used by base station towers.
120 Degree Antenna Towers
Next time, we will continue discussing the AMPS system.
We will also look at how digital cellular systems differ from AMPS and look at what’s inside a cell phone and what a base station looks like.
smart paper boy|
Active In SP
Joined: Jun 2011
24-08-2011, 12:04 PM
CELL DIV.doc (Size: 830 KB / Downloads: 50)
1..INTRODUCTION TO CELL PHONES
1.1.HOW IT WAS INVENTED?
Inventor Martin Cooper
Launch year 1973
A mobile phone (also called mobile, cellular phone, cell phone or hand-phone is an electronic device used for full duplex two-way radio telecommunications over a cellular network of base stations known as cell sites
A mobile phone allows its user to make and receive telephone calls to and from the public telephone network which includes other mobiles and fixed line phones across the world. It does this by connecting to a cellular network owned by a mobile network operator. A key feature of the cellular network is that it enables seamless telephone calls even when the user is moving around wide areas via a process known as handoff or handover.
Modern mobile phones also support many additional services, and accessories, such as SMS (or text) messages, email, Internet access, gaming, Bluetooth, infrared, camera, MMS messaging, MP3 player, radio and GPS. Low-end mobile phones are often referred to as feature phones, whereas high-end mobile phones that offer more advanced computing ability are referred to as smart-phones.
The first handheld cellular phone was demonstrated by Martin Cooper of Motorola in 1973, using a handset weighing in at two kilos.
By the end of 2009, only 20 years later, the number of mobile cellular subscriptions worldwide reached approximately 4.6 billion, 370 times the 1990 number, penetrating the developing economies and reaching the bottom of the economic pyramid.
1.2.HOW IT WAS DEVELOPED?
An evolution of mobile phone
The first mobile telephone call made from a car occurred in St. Louis, Missouri, USA on June 17, 1946, but the system was impractical from what is considered a portable handset today
In 1960, the world’s first partly automatic car phone system, Mobile System A (MTA), was launched in Sweden. MTA phones were composed of vacuum tubes and relays, and had a weight of 40kg. In 1962, a more modern version called Mobile System B (MTB) was launched, which was a push-button telephone, and which used transistors in order to enhance the telephone’scalling capacity and improve its operational reliability. In 1971 the MTD version was launched, opening for several different brands of equipment and gaining commercial success.
Martin Cooper, a Motorola researcher and executive is considered to be the inventor of the first practical mobile phone for hand-held use in a non-vehicle setting, after a long race against Bell Labs for the first portable mobile phone. Using a modern, if somewhat heavy portable handset, Cooper made the first call on a hand-held mobile phone on April 3, 1973 to his rival, Dr. Joel S. Engel of Bell Labs.
|Popular Searches: cell phones at school, cell phones boost mobile, dremel 395, go javass bbsr cont no, how cell phones towers work ppt, cell processor for ps3, using cell phones for robotics,|