Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
seminar class
Active In SP

Posts: 5,361
Joined: Feb 2011
24-02-2011, 10:55 AM

.doc   powersupply.doc (Size: 512 KB / Downloads: 130)
The input to the circuit is applied from the regulated power supply. The a.c. input i.e., 230V from the mains supply is step down by the transformer to 12V and is fed to a rectifier. The output obtained from the rectifier is a pulsating d.c voltage. So in order to get a pure d.c voltage, the output voltage from the rectifier is fed to a filter to remove any a.c components present even after rectification. Now, this voltage is given to a voltage regulator to obtain a pure constant dc voltage.
Usually, DC voltages are required to operate various electronic equipment and these voltages are 5V, 9V or 12V. But these voltages cannot be obtained directly. Thus the a.c input available at the mains supply i.e., 230V is to be brought down to the required voltage level. This is done by a transformer. Thus, a step down transformer is employed to decrease the voltage to a required level.
RECTIFIER: The output from the transformer is fed to the rectifier. It converts A.C. into pulsating D.C. The rectifier may be a half wave or a full wave rectifier. In this project and implimentation, a bridge rectifier is used because of its merits like good stability and full wave rectification.
Capacitive filter is used in this project and implimentation. It removes the ripples from the output of rectifier and smoothens the D.C. Output received from this filter is constant until the mains voltage and load is maintained constant. However, if either of the two is varied, D.C. voltage received at this point changes. Therefore a regulator is applied at the output stage.
Voltage regulator:
As the name itself implies, it regulates the input applied to it. A voltage regulator is an electrical regulator designed to automatically maintain a constant voltage level. In this project and implimentation, power supply of 5V and 12V are required. In order to obtain these voltage levels, 7805 and 7812 voltage regulators are to be used. The first number 78 represents positive supply and the numbers 05, 12 represent the required output voltage levels.A variable regulated power supply, also called a variable bench power supply, is one where you can continuously adjust the output voltage to your requirements. Varying the output of the power supply is the recommended way to test a project and implimentation after having double checked parts placement against circuit drawings and the parts placement guide.
This type of regulation is ideal for having a simple variable bench power supply. Actually this is quite important because one of the first project and implimentations a hobbyist should undertake is the construction of a variable regulated power supply. While a dedicated supply is quite handy e.g. 5V or 12V, it's much handier to have a variable supply on hand, especially for testing.
Most digital logic circuits and processors need a 5-volt power supply. To use these parts we need to build a regulated 5-volt source. Usually you start with an unregulated power supply ranging from 9 volts to 24 volts DC (A 12 volt power supply is included with the Beginner Kit and the Microcontroller Beginner Kit.). To make a 5 volt power supply, we use a LM7805 voltage regulator IC (Integrated Circuit). The IC is shown below.
The LM7805 is simple to use. You simply connect the positive lead of your unregulated DC power supply (anything from 9VDC to 24VDC) to the Input pin, connect the negative lead to the Common pin and then when you turn on the power, you get a 5 volt supply from the Output pin.
Brief description of operation: Gives out well regulated +5V output, output current capability of 100 mA
Circuit protection: Built-in overheating protection shuts down output when regulator IC gets too hot
Circuit complexity: Very simple and easy to build
Circuit performance: Very stable +5V output voltage, reliable operation
Availability of components: Easy to get, uses only very common basic components
Design testing: Based on datasheet example circuit, I have used this circuit successfully as part of many electronics project and implimentations
Applications: Part of electronics devices, small laboratory power supply
Power supply voltage: Unregulated DC 8-18V power supply
Power supply current: Needed output current + 5 mA
Component costs: Few dollars for the electronics components + the input transformer cost.
Active In SP

Posts: 2
Joined: Mar 2011
15-03-2011, 07:54 PM

i want abstract on 15 step digital power supply .......
Active In SP

Posts: 2
Joined: Mar 2011
15-03-2011, 09:20 PM

i want clear explaination about 15 step digital power supply

Important Note..!

If you are not satisfied with above reply ,..Please


So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page
Tagged Pages: project report on 5v power supply, seminar report dc regulated power supply, power supply usig ic7805 and ic7812, 5 volt regulator, 15 step digital power supply, project report 12v regulated power supply, regulated power supply,
Popular Searches: 7805 datasheet ppt, ece project topics with output, should internet speech be regulated, full discription of 15 step digital power supply, regulated power supply in seminaprojects, explaination of construction of regulated power, fptree java program with output,

Quick Reply
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  SEMINAR ON MICRO-HYDRO POWER PLANT PPT study tips 1 937 01-04-2016, 12:07 PM
Last Post: mkaasees
  spurious-power suppression technique (SPST) seminar tips 2 527 12-03-2016, 03:31 PM
Last Post: mkaasees
  POWER FORMER -New trend in powersystem study tips 1 1,211 31-03-2015, 07:03 AM
Last Post: Shahid.jan18@gmail.com
  DETECTING POWER GRID SYNCHRONIZATION FAILURE seminar addict 5 4,261 09-01-2015, 08:16 PM
Last Post: Guest
  automatic power saving conveyor for industrial application jaseelati 0 413 07-01-2015, 04:30 PM
Last Post: jaseelati
  HEAD MOTION CONTROLLED POWER WHEELCHAIR seminar class 8 7,426 21-10-2013, 10:30 PM
Last Post: Guest
  Electric Traction Supply System on Indian Railways project report helper 12 17,274 30-09-2013, 08:05 PM
Last Post: Guest
  Advanced FACTS Devices and Applications: Performance, Power Quality and Cost Consider seminar projects maker 0 1,334 28-09-2013, 04:54 PM
Last Post: seminar projects maker
  A SPURIOUS-POWER SUPPRESSION TECHNIQUE FOR MULTIMEDIA/DSP APPLICATIONS pdf seminar projects maker 0 1,474 28-09-2013, 03:25 PM
Last Post: seminar projects maker
  TYPES OF POWER SYSTEM TRANSIENTS REPORT seminar projects maker 2 1,184 27-09-2013, 09:34 AM
Last Post: seminar projects maker