Safety Rules For Different Zones in Industrial Automation full report
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
project topics
Active In SP

Posts: 2,492
Joined: Mar 2010
06-04-2010, 09:12 PM

.ppt   Safety Rules For Different Zones in Industrial Automation.ppt (Size: 1.31 MB / Downloads: 210)

Safety Rules For Different Zones in Industrial Automation


Safety is a situation, whereby the risk is not
greater than the limit risk.

Risk is a combination of the probability and the
degree of the possible injury or damage to health
in a hazardous situation.

Safety is relative.

There is no such thing as 100% safety.


ANSI:- American National Standards Institute.
IEC:- International Electrotechnical Commission.
DIN:- Deutsches Institute of Normung
OSHA:- Occupational Safety and Health Administration
EU:- European economic Union (EN-standards)

Risk analysis:

Determination of the Limits of Machinery
All phases of machinery life
The limits of machinery including the intended use
The full range of foreseeable uses of the machinery
The anticipated level of training, experience, and ability of the user
Exposure of other persons to the hazards of the machinery
Hazard Identification
Risk Estimation

Risk Evaluation and Reduction

Safe machinery design

Protection measures for the risks that canâ„¢t be eliminated

Inform users of the residual risks

Information, instruction, training and supervision

Use of Personal Protection Equipment

Area Guarding

Switch off power when a person enters the hazard area
Prevent switching on power when a person is in the hazard area.

Choice of Protective Measures

1. Preventing access during dangerous motion
Fixed Guards
Movable Guards
Two-Hand Controls
Preventing dangerous motion during access.
Photoelectric Light Curtains
Pressure Sensitive Safety Mats
Pressure Sensitive Edges


The muting conditions defined in IEC 61508:
a. Muting is only permitted to be activated during the time span of the working cycle
b. Muting must be performed automatically.
c. Muting must not depend on a single electrical signal.
d. Muting must not depend completely on software signals.
e. The muting signals, if they occur as part of an invalid combination, must not permit any muting state.
f. The muting state is removed immediately after the pallet has passed through

The safety distance

OSHA Formula:
Ds = 63 X TS where Ds= Safety Distance
63 = Recommended hand speed in in/sec
TS = Total stop time in Sec
ANSI Formula:
Ds = K x (Ts + Tc + Tr + Tbm) + Dpf
Ds = The minimum safe distance
K = 63 (hand speed in in/sec)
Ts = Stopping time of machine, in seconds
Tc = Control circuit response time in seconds
Tr = Light curtain response time
Tbm = Response time of a brake monitor
Dpf = Depth penetration factor
S = (K x T) + C K = 1600mm/sec assumed operator speed
T = The overall stopping time of the system
C = Depth of penetration
S = Safety distance


High efficiency is required
High accuracy is required
Complexity increases
Terrorism increases
Safety is required
Use Search at wisely To Get Information About Project Topic and Seminar ideas with report/source code along pdf and ppt presenaion

Important Note..!

If you are not satisfied with above reply ,..Please


So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page
Tagged Pages: safety rules for different zones in industrial automation pdf, safety measurements in automation, safety and industrial automation ppt, industrial hazard zones, automation hazard zones, safety measures in automation, safety rules and policies of automation industries,
Popular Searches: controlling a large data acquisition system using on industrial scada system, gujarat traffic rules gujrati pdf, seminar on industrial automation, hazardous waste management and handling rules 1989, fuzzy rules for malaria, industrial safety project topic, meaning of pervasivepervasive computing pdf,

Quick Reply
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  robots in radioactive environment full report project report tiger 14 16,536 27-04-2015, 07:00 PM
Last Post: Guest
  gsm based home automation system ppt jaseelati 0 204 07-02-2015, 03:02 PM
Last Post: jaseelati
  manufacturing automation protocol ppt jaseelati 0 141 23-12-2014, 01:52 PM
Last Post: jaseelati
  arduino projects from home automation to rocket control pdf jaseelati 0 342 09-12-2014, 02:50 PM
Last Post: jaseelati
  Pistonless Pump for Rockets full report and ppt project topics 8 10,468 15-11-2014, 04:08 PM
Last Post: mkaasees
  DRAG REDUCTION IN SHIPS USING MICROBUBBLES TECHNOLOGY full report project report tiger 4 7,425 24-03-2014, 04:27 PM
Last Post: seminar project topic
  Testing Of Bearings on Sound and Vibration Quality full report seminar class 1 2,443 09-10-2013, 03:16 PM
Last Post: Guest
  machine gun full report project report tiger 3 5,614 08-10-2013, 07:04 PM
Last Post: pc-alert
  micromachining full report project report tiger 4 10,068 02-09-2013, 10:10 AM
Last Post: study tips
  SUSPENSION SYSTEM full report seminar topics 18 29,477 20-08-2013, 07:43 PM
Last Post: vishnuts