Solid Waste Management
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
computer science crazy
Super Moderator

Posts: 3,048
Joined: Dec 2008
07-04-2009, 10:58 PM

In early times, the disposal of human and other wastes did not pose a significant problem, for the population was small and the amount of land available for the assimilation of wastes was large .Now due to rapid population growth and economic development in the country-Solid waste disposal has become a major environmental issue in India. Solid waste, often called the third pollution after air and water pollution, is that material which arises from various human activities and which is normally discarded as useless or unwanted it consists of the highly heterogeneous mass of discarded materials from the urban community as well as the more homogeneous accumulation of agricultural, industrial and mining wastes. In India authentic information regarding the composition of urban waste is not generally available,as regular analysis of the refuse is not carried out by the munipalities. Infact, refuse very heterogeneous in composition, and the geographical, temporal and seasonal variations in its composition make it difficult to define²typical refuse. The main constituents of urban wastes are similar through out the world, but the weight generated, the density and the proportion of constituents vary widely from country to country and from town to town with in a country according to level of economic development, geographic location, weather and social conditions. Similary the density of refuse in India is much higher than that of refuse generated in the cities of Western countries because of inclusion in it of the street sweepings.MSW in cities is collected and transported to designated disposal sites, which are normally low lying areas on out-skirts of the city. Open dumping of garbage facilitates the breeding for disease vectors such as flies,mosquitoes,rats and other pests. The municipalities in India therefore face the challenge of reinforcing their available infrastructure for efficient municipal solid waste management and ensuring the scientific disposal of MSW by generating enough revenues either from generators or by identifying activities that generate resources from waste management.
Use Search at wisely To Get Information About Project Topic and Seminar ideas with report/source code along pdf and ppt presenaion
Sauryajit Panda
Active In SP

Posts: 3
Joined: Oct 2009
14-10-2009, 09:27 PM

pl send more details about the topic solid waste management
computer science crazy
Super Moderator

Posts: 3,048
Joined: Dec 2008
16-10-2009, 12:02 PM

Waste management is the collection, transport, processing, recycling or disposal, and monitoring of waste materials The term usually relates to materials produced by human activity, and is generally undertaken to reduce their effect on health, the environment or aesthetics. Waste management is also carried out to recover resources from it. Waste management can involve solid, liquid, gaseous or radioactive substances, with different methods and fields of expertise for each. It is usually undertaken by the mafia.Waste management practices differ for developed and developing nations, for urban and rural areas, and for residential and industrial producers. Management for non-hazardous residential and institutional waste in metropolitan areas is usually the responsibility of local government authorities, while management for non-hazardous commercial and industrial waste is usually the responsibility of the generator.

Disposal methods

Recycling methods
Biological reprocessing
Energy recovery

Use Search at wisely To Get Information About Project Topic and Seminar ideas with report/source code along pdf and ppt presenaion
seminar ideas
Super Moderator

Posts: 10,003
Joined: Apr 2012
27-07-2012, 10:17 AM

to get information about the topic "SOLID WASTE MANAGEMENT" full report ppt and related topic refer the link bellow
study tips
Super Moderator

Posts: 10,180
Joined: Feb 2013
06-08-2013, 12:54 PM

Solid waste management

.docx   Solid waste .docx (Size: 375.38 KB / Downloads: 45)


Solid waste management is one among the basic essential services provided by municipal authorities in the country to keep urban centres clean. Due to rapid urbanization and industrialization the production of various types of solid wastes which pose serious problem to the environment have been generated. So the disposal and reuse of solid industrial wastes like phosphogypsum, flurogypsum, fly ash, slag and lime sludge, etc. is significant in view of their availability and potential application. It is estimated that about 300 million tonnes of inorganic waste from industrial and mining sectors are generated every year in India. Advances in solid waste management resulted in alternative construction materials as a substitute to traditional building materials like bricks, blocks, tiles etc. The efforts are being made for recycling different wastes and utilize them in value added applications. Since almost every natural resources are over exploited and are at the verge of extinction it is the high time for all of us to live aside our traditional conservative approaches and to move forward with new alternatives which are eco friendly and techniques that leads towards a sustainable development. The setting and hardening occurred due to formation of cementitious A-S-H and C-S-H gel (A =Al2O3 , S =SiO2 , C =CaO, H = H2O ). The technologies have been developed at bench scale and efforts are underway for scaling up to pilot plant level. This report aims at studying the recycling and utilisation of industrial wastes in making value added building materials.


The concept of industrial ecology is based on integration of by-product and waste steams across industries leading to production of useful products with near zero flow of material to the environment. Building industry is one of the most dynamic sectors with enormous potential of industrial symbiosis and synergistic utilisation of industrial wastes. With increasing environmental wariness, there is growing concern worldwide for updating production processes, as well as development of green building materials. The green material can be defined as products made from waste, recycled or by-productsto conserve natural resources, circumvent toxic and other emissions, saves energy, and contribute towards a safe and healthy environment. Geopolymers, silico-aluminate materials formed through mimicking natural rock forming process, are fast emerging as new class of green building construction materials. In the process of geo-synthesis, silicon (Si) and aluminium (Al) atoms react to form molecules that are chemically and structurally comparable to those binding natural rock and allows for novel products synthesis that exhibit the most ideal properties of rock-forming elements, i.e., hardness, chemical stability and longevity. Fly ash, blast furnace slag and red mud are the three major industrial wastes in India.


Most proposed mechanisms of geopolymerisation consist of dissolution of aluminosilicate phase, polymerisation and re-precipitation of gel phase, and transformation of the gel phase into geopolymer of varying crystallinity and structure. Depending upon experimental conditions, the different stages of geopolymer formation may overlap and even merge with each other. Isothermal conduction calorimetry was used to study the geopolymerisation of fly ash, mixture of (GBFS+fly ash), and the mixture containing (fly ash+GBFS+red mud).



Low reactivity of fly ash has often restricted the use of fly ash for geopolymer cements due to slow strength development. The reactivity of fly ash depends on its vitreous phase content, which participates in geopolymerisation reaction. The remaining constituents takes longer time for reaction due to poor reactivity and leads to slow setting and strength development in geopolymers. Various methods such as chemical activation, mechanical activation and size classification of fly ash has been suggested as a means to improve the reactivity. Recently observations were made by the present authors that use of mechanically activated fly ash leads to high compressive strength in geopolymers. Two different approach were adopted to enhance reactivity of fly ash: (a) air classification to separate finer fractions, and (b) mechanical activation in attrition and vibratory mills. Small size cenosphere cools faster during their formation in coal combustion process and separation of finer fraction by air classification results in increase in the glass contents vis-à-vis raw fly ash. Mechanical activation results due to combined effect of particle breakage (surface area) and other bulk and surface physicochemical changes induced by the process of milling.


Conventionally ceramic tiles are produced by high temperature sintering/ vitrification of aluminosilicate and silicate minerals such as clay, quartz, feldspar, etc. The strength and other properties of tiles are developed due to formation of ceramic bonds. Development of stoneware tiles at 250-400°C by geopolymerisation of alumino-silicate minerals has been reported. The processing involved reaction between aluminosilicate mineral kaolinite and NaOH at 100°C-150°C resulting into the formation of hydro-sodaliteSi2O5 , Al2(OH)4  + NaOH⇒Na(-Si-O-Al-O)n kaolinitehydro sodalite. In the alkali activation of fly ash and slag mixture at ambient temperature, fly ash/slag ratio is the most relevant factor on the strength development. The main reaction product is a hydrated calcium silicate with high amount of tetra-coordinated Al in its structure. The additions of calcium content increase the degree of geopolymerisation at elevated temperature and results into higher strength. Beneficial effect of slag on fly ash geopolymerisation was exploited in the development of self glazed wall tiles.
The glazed surface and the body of tiles showed distinctly different microstructure as revealed by SEM micrographs shown in Fig 4.5a and Fig 4.5b, respectively.


Pavement tiles are small cement structures in geometrical shapes that are usually laid on pathways or on any open ground as a solid platform. As these tiles are not cemented and only laid closely over a bed of loose sand, they can be easily removed, stored and reused as many times as possible. In India, the pavement tiles are mostly vibro-cast and/or pressed cement mortar or concrete hydrated for 28 days. The strength is obtained due to hardening of cement. Earlier research on alkali-slag-red mud-cement (ASRC) has indicated high early and ultimate strength together with excellent resistance against chemical attacks. This was achieved by introduction of solid composite alkali activator into slag–red mud mixture system instead of liquid water glass. The hydration products of ASRC cement were mostly C-S-H gel with low Ca/Si ratio in the range of 0.8 to 1.2.


Synergistic use of industrial waste is an emerging concept whereby combination of two or more wastes is used to develop a useful product. The main advantage of the synergy is the deficiency of constituents from one waste is compensated by using second or third waste, which is rich in deficient constituent. Synergistic use also includes industrial symbiosis where physical exchange of waste/by-products between geographically close industries is exploited. In the present work, waste from three industries, fly ash from thermal power plants, fly ash and granulated blast furnace slag from Steel Plants, and fly ash and red mud from Aluminium plants, has been used.
Fly ash was used for the development of geopolymers cement, combination of fly ash and blast furnace slag was used for self-glazed tiles and all three wastes fly ash, GBFS and red mud was used for pavement tiles. From the point of view of zero or minimum flow into environment, geopolymer cement is best suited for thermal power plant, where fly ash is the main by-product. Self-glazed tiles and pavement tiles are more suitable for iron & steel and aluminium industry respectively. Fig.5.1 shows the synergy map of these wastes.


 Due to their ability to polycondense Silicon and Aluminium into solid monolithic ceramic like structure during alkali activation, geopolymers have the potential of utilization of industrial wastes rich in silico-aluminates such as fly ash, GBFS, red mud, etc. Novel building materials such as high strength geopolymers cement can be developed by additional processing such as mechanical activation, and self-glazed tile and pavement tiles can be developed by synergistic use of industrial waste namely fly ash, GBFS and red mud. The developed geopolymer products qualify as new members in the spectrum of eco-friendly construction materials due to easy and simple processing, low energy requirement and no CO2 emission. The products have good commercialisation potential with significant returns.

Important Note..!

If you are not satisfied with above reply ,..Please


So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page
Tagged Pages: waste management seminar topic, solid waste management use in civil engineering ppt, solid waste management seminar topic, solid waste management in rural areas of india filetype ppt, civi seminar solid waste management, solid waste management seminar, waste management practices differ for developed and developing nations,
Popular Searches: solid waste ppt, solid waste managment ppt, a full project on solid waste management free download, full report of solid waste management for civil engineering seminar, solid waste management seminar pdf, civil ppt in solid waste managenent, seminar on solid waste management,

Quick Reply
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  construction waste recycling full report project report tiger 3 5,598 21-03-2015, 07:15 PM
Last Post: Guest
  SOIL STABILIZATION BY WASTE PLASTIC FIBERS summer project pal 12 20,591 15-12-2014, 09:56 PM
Last Post: Guest
  A PRESENTATION ON Potential Re-use of Plastic Waste in Road Construction: A Review study tips 1 2,429 12-11-2013, 01:01 PM
Last Post: Guest
  SOLID WASTE MANAGEMENT (SWM) ppt study tips 0 703 02-08-2013, 04:00 PM
Last Post: study tips
  Effect of Waste Polymer Materials on Shear Strength of Unsaturated Clays Report study tips 0 599 17-07-2013, 03:24 PM
Last Post: study tips
  Building Maintenance Management System for Heritage Museum pdf study tips 1 1,089 30-05-2013, 10:38 AM
Last Post: Halan
  Environmentally Sound Options for E-Waste Management Report study tips 0 651 17-04-2013, 03:48 PM
Last Post: study tips
  E-Waste Management in India: Issues and Solutions Report study tips 0 636 26-02-2013, 04:44 PM
Last Post: study tips
  Roads from plastic waste pdf study tips 1 1,063 23-02-2013, 02:20 PM
Last Post: Guest
  The Application of Check Dams Construction to Watershed Management: A case study study tips 0 664 11-02-2013, 02:10 PM
Last Post: study tips