Synthesis Control of Switching Topologies of Converters full report
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
project topics
Active In SP

Posts: 2,492
Joined: Mar 2010
12-04-2010, 11:19 PM

.doc   Synthesis Control of Switching Topologies of Converters.doc (Size: 149 KB / Downloads: 60)

Synthesis Control of Switching Topologies of Converters

An intelligent inference pipeline for the control of a dc-dc buck-boost converter was designed and built using a semi-custom. The switching topologies of the converter was mapped into a look-up table that was synthesized into controllers, and detectors for building complete instrument systems.
Two different topologies are called buck“boost converter. Both of them can produce an output voltage much larger (in absolute magnitude) than the input voltage. Both of them can produce a wide range of output voltage from that maximum output voltage to almost zero.
The inverting topology “ The output voltage is of the opposite polarity as the input
A buck (step-down) converter followed by a boost (step-up) converter “ The output voltage is of the same polarity as the input, and can be lower or higher than the input. Such a non-inverting buck-boost converter may use a single inductor that is used as both the buck inductor and the boost inductor.
The buck“boost converter is a type of DC-DC converter that has an output voltage magnitude that is either greater than or less than the input voltage magnitude. It is a switch mode power supply with a similar circuit topology to the boost converter and the buck converter. The output voltage is adjustable based on the duty cycle of the switching transistor. One possible drawback of this converter is that the switch does not have a terminal at ground; this complicates the driving circuitry. Also, the polarity of the output voltage is opposite the input voltage. Neither drawback is of any consequence if the power supply is isolated from the load circuit (if, for example, the supply is a battery) as the supply and diode polarity can simply be reversed. The switch can be on either the ground side or the supply side.
There are two types of converters they are described as follows,
A buck converter is a step-down DC to DC converter. Its design is similar to the step-up boost converter, and like the boost converter it is a switched-mode power supply that uses two switches (a transistor and a diode), an inductor and a capacitor.
The simplest way to reduce a DC voltage is to use a voltage divider circuit, but voltage dividers waste energy, since they operate by bleeding off excess power as heat; also, output voltage isn't regulated (varies with input voltage). Buck converters, on the other hand, can be remarkably efficient (easily up to 95% for integrated circuits) and self-regulating, making them useful for tasks such as converting the 12 - 24 V typical battery voltage in a laptop down to the few volts needed by the processor.
Theory of Operation
When the switch pictured above is closed (On-state, top of figure 2), the voltage across the inductor is VL = Vi - Vo. The current through the inductor rises linearly. As the diode is reverse-biased by the voltage source V, no current flows through it;
When the switch is opened (off state, bottom of figure 2), the diode is forward biased. The voltage across the inductor is VL = - Vo (neglecting diode drop). The current IL decreases.
The operation of the buck converter is fairly simple, with an inductor and two switches (usually a transistor and a diode) that control the inductor. It alternates between connecting the inductor to source voltage to store energy in the inductor and discharging the inductor into the load.
Continuous mode
A buck converter operates in continuous mode if the current through the inductor (IL) never falls to zero during the commutation cycle. In this mode, the operating principle is described by the chronogram
Discontinuous mode
In some cases, the amount of energy required by the load is small enough to be transferred in a time lower than the whole commutation period. In this case, the current through the inductor falls to zero during part of the period. The only difference in the principle described above is that the inductor is completely discharged at the end of the commutation cycle.
Evolution of the voltages and currents with time in an ideal buck converter operating in discontinuous mode.
We still consider that the converter operates in steady state. Therefore, the energy in the inductor is the same at the beginning and at the end of the cycle (in the case of discontinuous mode, it is zero). This means that the average value of the inductor voltage (VL) is zero, i.e that the area of the yellow and orange rectangles in figure 5 are the same. This yields:
So the value of d is:
Discontinuous mode
As told at the beginning of this section, the converter operates in discontinuous mode when low current is drawn by the load, and in continuous mode at higher load current levels. The limit between discontinuous and continuous modes is reached when the inductor current falls to zero exactly at the end of the commutation cycle.
Efficiency factors
Conduction losses that depend on load:
Resistance when the transistor or MOSFET switch is conducting.
Diode forward voltage drop (usually 0.7 V or 0.4 V for schottky diode)
Inductor winding resistance
Capacitor equivalent series resistance
Switching losses:
Voltage-Ampere overlap loss
Frequencyswitch*CV2 loss
Reverse latence loss
Losses due driving MOSFET gate and controller consumption. Transistor leakage current losses, and controller standby consumption.[4]
1. ^ Guy Séguier, Électronique de puissance, 7th edition, Dunod, Paris
2. ^ Tom's Hardware: "Idle/Peak Power Consumption Analysis"
3. P. Julián, A. Oliva, P. Mandolesi, and H. Chiacchiarini, Output discrete feedback control of a DC-DC Buck converter, in Proceedings of the IEEE International Symposium on Industrial Electronics (ISIE™97),
Use Search at wisely To Get Information About Project Topic and Seminar ideas with report/source code along pdf and ppt presenaion

Important Note..!

If you are not satisfied with above reply ,..Please


So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page
Popular Searches: rf control switching project report, type of control dc motors dual converters, sdtv converters, topologies ppt, latest works on green synthesis, ppt topics on converters 2012, pon topologies cse seminar report,

Quick Reply
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  electronic diesel control edc pdf jaseelati 0 301 17-02-2015, 03:09 PM
Last Post: jaseelati
  vhdl code for elevator control system jaseelati 0 243 23-12-2014, 03:27 PM
Last Post: jaseelati
  witricity full report project report tiger 28 38,075 30-08-2014, 02:26 AM
Last Post:
  Ultrasonic Sensor Based DC Motor Control Using LabVIEW seminar class 5 5,236 05-05-2014, 10:08 AM
Last Post: seminar project topic
  ACCIDENT PREVENTION USING WIRELESS COMMUNICATION full report computer science topics 5 7,570 17-04-2014, 11:07 AM
Last Post: seminar project topic
  silicon on plastic full report computer science technology 2 2,931 13-04-2014, 10:34 PM
Last Post: 101101
Last Post: seminar project topic
  Automatic Emergency Light full report seminar class 7 17,561 08-03-2014, 02:28 PM
Last Post: seminar project topic
  ACD-Anti Collision Device full report seminar presentation 11 18,177 10-01-2014, 03:20 PM
Last Post: seminar project topic
Last Post: seminar project topic